Somfy DECOFLEX WIREFREE RTS Bedienungsanleitung PDF herunterladen

STOP

Thin side over outer edge of box

3. Place the flat side of mounting

bracket (included) against the wall

and align the thin side over the

outside edge of the existing

electrical box (opposite the stud

side). Center the bracket to align

the mounting screw height with

existing switch, then trace the

inside shape of the bracket on wall

using a pencil or thin marker.

4. Using a dry-wall saw (or

similar) begin to cut the dry-

wall along the traced outline.

Do not cut hole larger than

outline as this may result in

a loose fitting bracket. *For

greater accuracy please

refer to the recommended

hole dimensions on reverse

page.

The DecoFlex RTS Switch is a wireless radio transmitter compatible with all Somfy RTS Motors and

externally mounted RTS receivers.

The Somfy DecoFlex WireFree RTS switch is a low voltage device which in many cases does not require

an electrical box. It can be mounted adjacent to an existing Decora style light switch or as a stand-alone

device using the (included) SOMFY low voltage mounting bracket (See installation section for details).

- Power: 3V lithium battery, CR 2450 type

o o o o

- Operating temperature: +5 C/41 F to +40 C/104 F

- Range: Up to 65 Ft.

- Fits into standard Decora Wall Plates

Commands are transmitted by radio waves at 433.42 MHz.

Programming/Operating/Assembly Installation Instructions

DecoFlex WireFree RTS Switch

DESCRIPTION

PROGRAMMING

1 CHANNEL

White: 1810897

Ivory: 1810898

Black: 1810899

A. ADDING A DECOFLEX WIREFREE RTS WALL SWITCH - INITIAL INSTALLATION

NOTE: During initial programming it is recommended to provide power only to the motor or RTS receiver being programmed.

1. Set the RTS Receiver or Motor into Programming Mode (Refer to the installation instructions of the relevant RTS receiver or motor for this procedure).

2. Select a Channel to be memorized by pressing the appropriate CHANNEL BUTTON. The adjacent LED will light to indicate the channel has been selected. (See figure 1)

3. Using a paperclip or similar device, briefly press the programming button (1 second max) located on the DecoFlex WireFree switch (See figure 1). The RTS receiver or motor will

confirm the addition of the new DecoFlex switch in their respective manners.

FIGURE 1

C. DELETING SPECIFIC CHANNELS OR DECOFLEX WIREFREE WALL SWITCH FROM MEMORY

1. Using a paperclip or similar device, press and hold the program button (for 3 seconds) on a previously addressed DecoFlex

switch or channel in memory (See figure 1). NOTE: This SHOULD NOT be performed with the device or channel intended for deletion.

The RTS receiver or motor will confirm programming mode in their respective manners.

2. Select a Channel to be deleted by pressing the appropriate CHANNEL BUTTON. The adjacent LED will illuminate to indicate the channel has been selected (See figure 1).

NOTE: Only one channel can be deleted per procedure. To remove/delete additional channels, proceed to Step 3 then start at Step 1 for each channel to be deleted.

3. Using a paperclip or similar device, briefly press the programming button (1 second max) located on the DecoFlex switch (See figure 1). The RTS receiver or motor will

confirm the deletion of the selected channel or DecoFlex switch in their respective manners.

B. ADDING ADDITIONAL CHANNELS OR DECOFLEX WIREFREE WALL SWITCHES

1. Using a paperclip or similar device, press and hold the program button (for 3 seconds) on the previously addressed DecoFlex

switch or channel in memory. The RTS receiver or motor will confirm programming mode in their respective manners.

2. Select a NEW channel or DecoFlex switch to be memorized by pressing the appropriate CHANNEL BUTTON.

The adjacent LED will illuminate to indicate the channel has been selected (See figure 1).

3. Using a paperclip or similar device, briefly press the programming button (1 second max) located on the DecoFlex

switch (See figure 1). The RTS receiver or motor will confirm the addition of the new channel or DecoFlex switch

in their respective manners.

Program

Button

Select the

Channel

Button(s)

OPERATING THE DECOFLEX WIREFREE WALL SWITCH

1. Select the CHANNEL BUTTON(s) programmed to a specific window covering(s). The adjacent LEDs will illuminate

to indicate the channel(s) selected (press CHANNEL BUTTON(s) in successive order to DESELECT,the adjacent LEDs

will extinguish to indicate the deselected channels).

2. To raise the window covering(s), press the UP button. To lower the window covering(s), press the DOWN button.

3. To stop the window covering(s) at any time, simply press the STOP button (see figure 2).

4. If a “Preferred Position” has been programmed, the window covering(s) can be commanded to travel to a preprogrammed

intermediate position.(Refer to the installation instructions of the relevant RTS receiver or motor for this procedure).

Select the

Channel

Button(s)

STOP

Button

DOWN

Button

FIGURE 2

LED

Indicator

LED

Indicator

5 CHANNEL

White: 1810813

Ivory: 1810814

Black: 1810830

INSTALLATION

Included is a special SOMFY low voltage device mounting bracket which attaches to drywall and eliminates the need for an electrical box.

The bracket can be used in two mounting type configurations, they are as follows:

1. The bracket is specifically designed for mounting the DecoFlex WireFree RTS wall switch to an adjacent (pre-existing) Decora style light switch (see below).

This

unique mounting bracket allows the necessary spacing for 2 adjacent switches and a new "Double Gang" (2 Gang) wall plate to be installed

(See photo 8) resulting

2. The bracket can also be used for individual or "stand-alone" (1 switch) mounting configurations.

NOTE: When following configuration 1. The mounting bracket is not designed to be used in

conjunction with "old-work” or retrofit electrical boxes.

1. Locate an existing light switch

and remove wall plate exposing

electrical box.

Somfy recommends shutting off

power to the exposed electrical box

prior to installation.

2. Using a stud sensor, locate

the stud nearest to exposed

electrical box. Then mark (for

reference) with removable

tape or pencil.

Screw drivers (Phillips and Bladed), Dry-wall saw, Wall stud sensor, Non-marring tape and pencil

Tools required for installation:

(Please check local codes to determine if an electrical box is required for your installation.)

in an aesthetically pleasing professional installation.

NOTE: If a command button (UP, DOWN, STOP,) is pressed without a channel button(s) selected, the DecoFlex will default to the channel button(s) previously selected.

Selecting multiple CHANNEL BUTTONS for “group” activation will result in a sequential-output whereby each channel will activate in sequence from channel 1-5.

Align

screw holes

STOP

For increased radio performance, Somfy recommends the use of non-metallic electrical enclosures.

1 2

Inhaltsverzeichnis

Seite 1 - DecoFlex WireFree RTS Switch

STOPSTOPThin side over outer edge of box3. Place the flat side of mounting bracket (included) against the wall and align the thin side over the outsid

Seite 2 - INSTALLATION CONT’D

Ref. No. 25018190SOMFY SYSTEMS, INC. 9/13CSOMFY SYSTEMS, INC. reserves the right to change, update or improve this document without prior notice.5.

Verwandte Modelle: DECOFLEX WIREFREE RTS TABLE TOP

Kommentare zu diesen Handbüchern

Keine Kommentare

Somfy DECOFLEX WIREFREE RTS Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Für Zuhause Somfy DECOFLEX WIREFREE RTS herunter. SOMFY DECOFLEX WIREFREE RTS User Manual Benutzerhandbuch

Inhaltsverzeichnis

Verwandte Modelle: DECOFLEX WIREFREE RTS TABLE TOP

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Für Zuhause Somfy DECOFLEX WIREFREE RTS